AUDIT® 1:1 Herbicide
Tribenuron-methyl Thifesulfuron-Methyl THIFENSULFURON + TRIBENURON METHYL
AUDIT® 1:1 Herbicide is the dependable first choice for post-emergence control of broadleaf weeds. AUDIT 1:1 provides consistent control on the toughest broadleaf weeds like Canada thistle, pigweed, lambsquarters, mustards and other post-emergence broadleaf weeds. AUDIT 1:1 also provides flexible crop rotation and enhanced grass performance when used with Group 2 herbicides like EVEREST® 3.0.
Jump to section
Additional Product Details
All Crops
- Canola
- Cotton
- Durum wheat
- Fall barley
- Fall wheat
- Fallow
- Field corn
- Grain sorghum
- Rape (see Rapeseed or Rape greens)
- Rice
- Rye
- Soybean
- Spring barley
- Spring oats
- Spring wheat
- Sugar beet
- Triticale
- Winter barley
- Winter oats
- Winter wheat
All Pests & Diseases
- Annual knawel
Quick Facts
- Convenient water-dispersible granule formulation
- Best used when weeds are young and actively growing
- Primarily absorbed through foliage to inhibit weed growth
TIMING
In crop:
- 2-leaf minimum, but before flag leaf is visible
- Do not harvest within 45 days of the last application
Can also be used for pre-plant burndown, post harvest and fallow. See AUDIT 1:1 label for specific use recommendations.
CROP ROTATION
Wheat (including durum) and barley may be replanted at anytime. Cotton can be planted 14 days after application. Sugar beets, winter rape and canola may be planted 60 days after application. All other crops can be planted 45 days after application.
RATE
Wheat (including durum), barley
- Low rate: 0.4 oz/A
- High rate: 1 oz/A
Pre-plant burndown, post-harvest and fallow
- Low rate: 0.4 oz/A
- High rate: 1 oz/A
Sequential treatments of AUDIT 1:1 Herbicide may also be made, provided the total amount of AUDIT 1:1 applied to the crop or during one fallow/pre-plant season does not exceed 1.0 oz/A.
TANK-MIX PARTNERS
Broadleaf Herbicide Tank-Mixes
2,4-D, MCPA; dicamba, bromoxynil and fluroxypyr-containing products
MIXING INSTRUCTIONS
Ground Application
Do not use with spray additives that alter the pH of the spray solution below pH 5.0 or above pH 9.0, as rapid product degradation can occur. Spray solutions of pH 6.0 to 8.0 allow for optimum stability of this product.
1. Fill the tank to 1/3 full of water.
2. While agitating, add the required amount of this product.
3. Continue agitation until this product is fully dissolved, at least 5 minutes.
4. Once this product is fully dissolved, maintain agitation and continue filling tank with water.
5. As the tank is filling, add tank-mix partners and then add the required volume of spray adjuvant. Always add spray adjuvant last. Antifoaming agents may be used. Do not use with spray additives that alter the pH of the spray solution below pH 6.0, as rapid product degradation can occur. Spray solutions of pH 7.0 and higher allow for optimum stability of this product.
6. Dispersed tank-mix partners can settle if the tank mixture is not continually agitated. If settling occurs, thoroughly re-agitate before using.
7. Apply this product spray mixture within 24 hours of mixing to avoid product degradation.
8. If this product and a tank-mix partner are to be applied in multiple loads, fully dissolve this product in clean water prior to adding to the tank.
PACKAGING
- 32 oz in one bottle
- 8 x 32 oz bottles per case
WATER VOLUME
- 5–20 gal/A for ground applications
- 2–5 gal/A for aerial applications